Home / Support / Book A Demo

Book A Demo

See how handheld fibre laser welding performs on your own stainless steel work, either at our Spartan base in Kempton Park or at your workshop. We help fabricators test fit-up, finish, speed and training needs before you commit to production.

Book A Demo

Choose the demo that suits your workshop

Most customers in Ekurhuleni start with a Spartan based demo in Kempton Park, then decide whether an onsite visit is needed. If you are dealing with kitchen equipment, tanks, railings, sheet metal or general stainless fabrication, we can set up a practical session around the type of joints you make every day.

For shops in Jet Park, Isando, Edenvale, Germiston, Boksburg and Alberton, an onsite visit often saves time because we can work on your actual material and see your real access issues. Small workshops, large production floors and contract fabricators all use the demo in different ways, so we keep it focused on the parts that matter to you.

Bring your own stainless parts if possible

The best results come from testing your own material, weld prep and joint gaps. If you can, bring offcuts, sample assemblies or drawings so we can show what the machine can do on the same grade and thickness you use in production.

  • Flat sheet, tube, angle, or formed stainless sections
  • Samples with visible fit-up issues or heat distortion concerns
  • Small jobs you want to speed up, or finishes you want to improve
  • PPE you normally use in the workshop, if the demo is onsite

If you do not have samples ready, we can still demonstrate common stainless applications and explain where the process saves time, where it needs good prep, and where a different setup may be better. That helps avoid guesswork, especially when your team is under pressure to keep jobs moving.

What happens during the demonstration

A typical session starts with a short discussion about your material, your welders experience level and the jobs you want to improve. Then we set up the handheld fibre laser welder, check the working area, and run test welds on the sections you brought in.

We show how the process handles clean seams, corner joints, tack correction and repeat work. We also talk through torch handling, travel speed, shielding needs and how to set the team up for consistent results. If your site has limited power or load-shedding planning to consider, we can discuss practical operating times and workflow too.

  • Machine commissioning and basic setup
  • Operator training on safe handling and technique
  • Weld testing on your own parts
  • Process optimisation for repeat work
  • Production rollout planning for larger teams

Book a Spartan session or an onsite visit

If you prefer to come to us, our Spartan demo point in Kempton Park is set up for focused demonstrations and training. That works well for decision makers who want to compare results, ask technical questions and bring samples in without taking the whole team off site.

If you need us at your factory, we can arrange visits across Gauteng and other parts of South Africa, subject to scheduling. We work with fabrication shops in places like Kempton Park, Germiston and Boksburg, as well as wider national sites where teams want hands on guidance at the machine.

What to prepare before you send the enquiry

Use the enquiry form on our contact page and give us enough detail to plan the visit properly. The more we know upfront, the better we can match the demo to your work, your space and your team size.

  • Your location and whether you want Spartan or onsite
  • The stainless grades and thicknesses you use most often
  • The type of joints, finishes, and production volumes you work with
  • How many operators should attend
  • Any training, maintenance, or process issues you want addressed

If you are comparing options for a new process, tell us what is slowing you down now. That may be excessive grinding, slow turnaround, poor repeatability or too much rework. A clear brief helps us show the right setup from the start, not a generic demo.

Support after the demo

The visit does not end when the test welds are done. If you move ahead, we can help with commissioning, refresher training, consumables support, spares supply, preventive maintenance and breakdown response. That support is useful for workshops that need steady output and do not want long delays when something needs attention.

For teams that are still building confidence, remote help and follow-up training can keep progress moving after the first session. Wynand Oosthuizen leads the business, with Tshegofatso Ramaboa on training, Gert Wessels on technical sales, Ayanda Mthembu on service, Reuben Daniels on applications and Sindisiwe Makhado on customer support. It means the person who books the demo can get practical answers, not sales talk.

Questions we get asked

Can we use our own stainless steel parts for the demo?

Yes, that is preferred where possible. Your own parts show real fit-up, thickness and finish requirements, so the results are more relevant to your workshop.

Do you only demo in Spartan, Kempton Park?

No. We can host demos at our Spartan base or arrange onsite visits at fabrication shops nationwide, subject to scheduling and location.

What should we include in the enquiry form?

Send your location, the type of stainless work you do, the thicknesses you use, how many people need training, and whether you want a demo, testing or follow-up support.

Book a handheld laser welding demo.

Contact form