Home / Support / Training Enquiry

Training Enquiry

Need hands on training for handheld fibre laser welding? Tell us what material you work with, where your shop is, and what level of support you need. We train operators, supervisors and teams on safe setup, weld quality and production use at your premises or at one of our Spartan demo locations.

Training Enquiry

What To Include In Your Training Enquiry

Use the enquiry form on our contact page and tell us as much as you can about your workshop. The more detail you share, the easier it is for us to match the session to your material, staff and daily output. We work with stainless steel fabricators in Spartan, Kempton Park, Isando, Jet Park, Edenvale, Germiston, Boksburg and Alberton, and we also travel to fabrication shops nationwide for demos and training.

Helpful details include your machine model, thickness range, material grades, and whether you need first time operator training or a refresher. If you are trying to reduce rework, improve bead appearance, or speed up production, say so in the form. That helps us focus on the practical points that matter on your shop floor, not theory alone.

  • Workshop location and nearest town
  • Number of operators or supervisors to train
  • Type of stainless steel work you do
  • Current issues such as burn through, distortion, slow cycle times or inconsistent seams
  • Your preferred dates and shift times

Operator Training Built Around Real Production Work

Our operator training is geared for fabricators who need clean, repeatable welds and a steady pace. We show your team how to set up the hand held fibre laser welder, prepare joints properly, handle the torch safely, and maintain consistent travel speed. For many shops the biggest gain comes from learning how to reduce grinding and rework, which saves time right away.

We can train new operators who have never used this type of equipment before, as well as experienced welders moving over from traditional methods. Sessions are practical and can be structured around your own parts, fixtures and material thicknesses. If your shop runs under load-shedding pressure or has limited bench space, we also cover daily setup habits that help keep production moving.

  • Safe machine start-up and shutdown
  • Focus on stainless steel joints and finish quality
  • Correct speed, angle and torch movement
  • Heat control to reduce distortion
  • Basic fault finding and when to call for support

Refresher Sessions For Teams That Need A Reset

Even a good team can lose consistency when staff change, shifts rotate or production gets busy. A refresher session is useful when weld quality starts drifting, operators need confidence back, or a new supervisor wants to standardise methods across the workshop. We often see this in small jobbing shops and larger manufacturing plants alike.

Refreshers can be short and focused. For example, we may spend a morning on weld quality checks, then move into afternoon production issues such as seam appearance, edge preparation and repeatable fit up. If you have recently added new staff, a refresher is a sensible way to get everyone aligned without slowing the whole shop down.

  • Ideal for teams after staff changes or machine relocation
  • Useful before a new production run or contract start
  • Helps correct bad habits before they affect output
  • Can be done at your premises or at our Spartan base

Production Focused Coaching For Higher Output

If your aim is not just training but better throughput, ask for production focused coaching. This is where we work alongside your operators on actual jobs and look at the full process from prep to final clean up. We check where time is being lost, where settings can be tightened, and where the weld sequence can be improved without compromising quality.

This kind of support is useful when you need to quote more competitively or meet tighter lead times. We can help with process optimisation, production rollout, weld testing and refresher training so the method used in training is the same method used on the floor. Small improvements in clamping, joint fit and travel discipline often make a measurable difference in output and finish.

Common coaching outcomes include shorter cycle times, less grinding, fewer rejects and easier handover between shifts. On a busy shop floor, that can mean a lot.

How The Training Booking Process Works

Once you submit the enquiry form, our team reviews your requirements and comes back with a suitable training plan. If needed, we may ask a few follow up questions about your material range, access on site and the number of people who must attend. For some shops, a demo first is the best starting point. For others, we go straight into operator training at the workshop.

Our process is straightforward:

  • Receive your enquiry through the contact page
  • Confirm your site, team size and welding needs
  • Recommend a training format and date
  • Carry out the session at your shop or at one of our demo locations
  • Follow up with support, spares or additional training if required

We also assist with machine commissioning, preventive maintenance, breakdown response and remote help when your team needs it after the session. That makes it easier to keep standards consistent over time, not just on the day of training.

Who Runs Your Session

Your training and support are handled by a local team based in Spartan, Kempton Park. Wynand Oosthuizen leads the business, with Tshegofatso Ramaboa heading national training, Gert Wessels on technical sales, Ayanda Mthembu coordinating service, Reuben Daniels handling applications support and Sindisiwe Makhado looking after customer queries. That mix of field experience and workshop knowledge helps us keep the advice practical.

Whether you are in Ekurhuleni or further afield, we focus on giving your team clear steps they can use immediately. If your shop is working through tight deadlines, municipal noise limits, or coastal humidity that affects storage and cleanliness, we can shape the session around those conditions too.

We will help you build that confidence in a way that suits your shop and your schedule.

Questions we get asked

Do you offer training at our workshop?

Yes. We can train your team at your fabrication shop anywhere in South Africa, or arrange a session at our Spartan and Kempton Park demo locations.

Can we book a refresher for experienced operators?

Yes. Refresher sessions are ideal for teams that need to standardise settings, improve weld consistency, or get new staff up to speed after changes in the workshop.

What should we prepare before the session?

Have your machine ready, clear the work area, and tell us what stainless steel thicknesses and joint types you work with. If you have problem parts, bring them along for a practical review.

Book a handheld laser welding demo.

Contact form