Built for curved stainless tanks and long seams
This package is aimed at stainless tank fabrication where round bodies, cone sections, nozzles and seam joints need a neat finish with steady travel speed. It is commonly used on water tanks, process tanks, dairy vessels, brewery fittings, chemical handling tanks and fabricated storage units. The handpiece gives fine control on heat input, so you can work along longer seams without the wide heat affected zone that often comes with older methods.
For shops doing mixed work, the same unit can handle straight seams, corner joints and repair work on already formed shells. That makes it practical for small teams in Germiston or larger manufacturing floors in Jet Park where one welder may move from tank seams to bracket repairs in the same shift.
- Designed for stainless steel tank fabrication
- Suitable for curved shells, seams and repair work
- Helps reduce post weld grinding on visible welds
- Useful on single jobs and repeat production runs
Available sizes and setup options
Laser-Welder supplies the tank fabrication package in output levels suited to light to medium stainless fabrication, with options to match your material thickness and output target. The right selection depends on whether you are working on thin tank skins, heavier flanges or longer continuous seams. A 1.5 kW setup is often enough for lighter workshop work, while 2 kW and 3 kW packages suit shops that want faster travel speed and more room for thicker sections.
We also help choose the right wire feed arrangement, torch head and travel settings for the type of tank you build. If your team works on 1.2 mm to 3 mm stainless, we look at fine control and neat edge control. If you are joining heavier vessels or reinforcement rings, we can specify a stronger setup for steadier production. Small typo sometimes happens in shop notes, but the important part is matching the machine to the job, not guessing.
- Power options commonly used: 1.5 kW, 2 kW, 3 kW
- Works with handheld fibre laser welding heads
- Can be specified for manual or production focused use
- Settings are matched to stainless thickness and seam length
Where this package fits best
This welder suits fabrication shops that make tanks for food, beverage, water treatment, plant rooms and general industrial use. It is especially helpful where finish quality matters, because tank bodies often show every mark once fitted and polished. In coastal areas such as Durban, Gqeberha and parts of the Western Cape, the cleaner weld profile also helps reduce rework on stainless exposed to humidity and chlorides.
It also fits workshops that struggle with labour pressure and power interruptions. A handheld fibre laser system can shorten welding time, and when load-shedding bites you are not burning through long hours on touch-up work afterwards. For municipal and site work, the neat seam finish can help where access is tight and grinding dust must be kept under control.
- Tank bodies and end caps
- Conical reducers and curved sections
- Nozzles, brackets and support pieces
- Repair jobs on stainless vessels already in service
Power, gas and workshop conditions
Installation needs a stable single phase or three phase supply depending on the package selected, with correct earthing and enough breaker capacity for the unit and chiller. We always check the site first so the machine is matched to the workshop supply and not tripping the panel every few minutes. If your shop runs on backup power during outages, that must be confirmed before commissioning so production planning stays realistic.
Shielding gas use depends on the job and material, but clean dry gas is important for neat stainless welds. For most tank work, argon based shielding is commonly used, and gas quality matters more than people think. Oil, moisture or contaminated hose lines can spoil the weld face and leave extra clean up. The machine itself should be installed in a dry area away from heavy dust, cutting sparks and direct spray. A bit of common sense here saves trouble later.
- Check supply voltage before installation
- Plan for earthing and breaker capacity
- Use clean dry shielding gas
- Keep the unit away from moisture, dust and grinding debris
Commissioning, training and support from Spartan
Every tank fabrication package can be commissioned at your workshop, with operator training included so your team can start correctly. We work from Spartan, Kempton Park and support demos in Kempton Park, Isando, Jet Park, Edenvale, Germiston, Boksburg and Alberton. Nationally, we also travel to fabrication shops for demonstrations and process checks when the work justifies it.
Training covers torch handling, speed control, seam overlap, cleaning, gas settings and basic troubleshooting. If your team has welded by other methods for years, we focus on practical changeover so they do not waste time guessing settings. Our service team also assists with breakdown response, remote help, preventive maintenance and production rollout when the machine moves from test work into full output.
- Machine commissioning at your workshop
- Operator and refresher training available
- Remote help for setup and process questions
- Support for production rollout and testing
What to check before you order
Before ordering, have clear answers on your typical stainless thickness, seam length, tank diameter and whether you need wire feed for gap filling. If you work mostly on curved shells, we need to know how tight the radius is and whether the job includes long continuous seams or short stitch runs. This helps us match the right head, power level and accessories for your line.
You should also confirm your workshop power, floor space, gas supply and whether the machine will be moved between bays. If you need on site training in Pretoria, Johannesburg, Vereeniging or further afield, tell us that early so we can plan the demo and setup. Start by sending your details through the contact form on the Laser-Welder South Africa site. Please include photos if you can, because a clear picture of the tank work tells us a lot.
- Stainless thickness and seam length
- Tank diameter and curved section details
- Need for wire feed or gap filling
- Power supply, floor space and gas arrangement
Key facts
| Laser power options | 1.5 kW, 2 kW, 3 kW |
|---|---|
| Material focus | Stainless steel tank fabrication |
| Typical thickness range | About 1.2 mm to 3 mm, depending on setup |
| Cooling | Integrated or external water cooling, depending on package |
| Power supply | Single phase or three phase, package dependent |
| Support areas | Spartan, Kempton Park and nationwide demos |





